A2 stainless steel socket cap bolt

 This part is available by special order, request a quote

Lower choke cable

Two lower cables are required. We advise you to measure your existing cable before ordering in case you have a non standard set up.

 This part is due back in stock soon, call 01484 841395 to reserve yours

12117001-z 12117001 GU12117001 12 11 70 01
 1211 7001 1211.7001 12.11.70.01

Lower throttle cable

We advise you to measure your existing cable before ordering in case you have a non standard set up

 This part is due back in stock soon, call 01484 841395 to reserve yours

12117501-z 12117501 GU12117501 12 11 75 01
 1211 7501 1211.7501 12.11.75.01

Clutch pushrod seal or pushrod bush

2 required. See CLA14901 for O ring alternative

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14085900 GU14085900 14 08 59 00
 1408 5900 1408.5900 14.08.59.00

Clutch plate kit consisting of 2 x friction plates, 1 x intermediate plate, deep splined clutch centre / boss and tabbed lock washer (not shown). For models with the early type shallow spline plates this is a worthwhile upgrade kit to the better deep splined centre and plates. Clutch plate alignment tool also available, see TOA30510. Suitable for all 5 speed dual plate clutch models

Save £20 on the cost of these components if bought seperately. Does not include clutch springs (see CLA13100). Thicker side of each friction plate should face transmission

 This part is due back in stock soon, call 01484 841395 to reserve yours

Shallow splined Newfren clutch friction plate for big twins with old shallow splined clutch centre

2 plates required per clutch overhaul- thicker side of each plate should face transmission. Also check your intermediate plate 12082300. This has shallower splines than the Spada 3 on plates. These are the best fit if you still have the original shallow spline clutch hub

 This part is available by special order, request a quote

28084460-z 28084460 GU28084460 28 08 44 60
 2808 4460 2808.4460 28.08.44.60

Left hand Domino type switchgear with high and low beam, pass, indicator and horn switches. Same style switch as ELA01738

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. An indication of wire colours is supplied with this switchgear. Supplied with 9 pin block connector. NB does not have lights off - park - on function, you need this to be on your RH switch (e.g. ELA01729 ) or run lights always on

 This part is available by special order, request a quote

CEV type lights (off/pilot/on), main beam and horn switch. Supplied without wires, you will need to solder your wiring into the switchgear using a minimum 60W soldering iron. Switch fixes to handlebars using included screws

Can be fitted to left or right side of bars

 This part is due back in stock soon, call 01484 841395 to reserve yours

12746001-z 12746001 GU12746001 12 74 60 01
 1274 6001 1274.6001 12.74.60.01

Distributor cap

May be supplied in black

 This part is due back in stock soon, call 01484 841395 to reserve yours

 12715432 GU12715432 12 71 54 32
 1271 5432 1271.5432 12.71.54.32

Old type 4 pin starter relay in metal case. Note that this has two large terminals and two smaller ones, depending on model you may need to fit wider spade connectors to fit this relay. See ELA10003 for large female spade connectors

 This part is due back in stock soon, call 01484 841395 to reserve yours

 12732500 GU12732500 12 73 25 00
 1273 2500 1273.2500 12.73.25.00